MR Bond Polychem

Room temperature curing filled epoxy casting compoud with hardener – 555, h – 1655 and h – 160

EC – 606 is specially developed for void free encapsulation and castings. EC – 606 is available in fuid easy to mix consistency ready for immediate application.

APPLICATIONS

· Casting, Potting and sealing of small and medium sized electrical and electronic components.

· Casting of switchgear components and insulators.

· Potting of instrument transformers.

· Cable joint insulation, with all types of cable such as PILC, PVC, Rubber insulated, etc.

· Topping of capacitors as sealant.

Additional Information:

• Pay Mode Terms: L/C (Letter of Credit)
• Port of Dispatch: Nhavashiva / Pipavav
• Production Capacity: 10000 kg
• Delivery Time: 15 days

CRYSTAL CLEAR URETHANE EPOXY 

FOR ART , CRAFT AND FOR 3D FLOORING

CRYSTAL CLEAR POLYURETHANE – EPOXY based  polymer adduct of gloss and adhesion improver are suitable for 3D  floorings  can apply on concrete,  Stone, wood and ceramics and laminated sheets specially developed  coating are transparent and  colored  application.

WHERETOUSE:- For 3D floor coating, Jewellery Meena, Gift articles, God idols, Key chain, wood, Marble, natural stone, concrete, ceramics, glass, ornamental metal,Appliances, Machineries, wall, Electric & electronics instruments, LED Encapsulating,  Paver  block and Tiles, Table top, Specially formulated for Inlay in stone and wood, etc.

METHOD OF USE:- (1)  SURFACE PREPARATION:-Surface should be Dry, clean, even and free from dust, dirt, paint, rust, Algee, grease, soluble salt, or other contaminations and Damp free.  Surface should be rough and clean.

(2) Apply Primer Coat:- Mix the polymer in given ratio and remove bubbles by applying vacuum for some time and vacuum the bubbled Air. (4) Apply the mixed polymer clear / colored ( Add small drop quantity for light color and add more drop quantity for dark color in to the clear polymer.Than apply on prepared surface by roller, brush or spray. 

(3) before 24 hours or after 4-6 hours (check apply screed coat before surface dry) Apply screed coat on primer coat for leveling is required. Mix as per given ratio. Make sure surface should be very smooth, if not prepared by sanding.

(4) Fix the choice design or a painted the designs:-Prepared painting or a fix the sheet of design as per your choice. If sheet is not self gumming , so apply any below Epoxy as a primer. Apply very thin coat.Aftre 24 hours.

(5) Apply last clear coat on designs:-Mix the part-A and Part-B in  given proportion, and apply on designs apply by roller, brush or a spray , as per suitable methods.

For Coating Thickness :- 3 mm to 5 mm will give better look 

For Casting Thickness :- 1 mm to 2 5 mm

TAKE CARE:- (1) take care dust should not damage of clarity of the last coat.(2) After mixing apply vacuum for removing air, If vacuum is not possible pass through mixed material from Doubal  layered Nylone/ Polyester fabrics for removing bubbles. (3)After applying clear coat apply spike roller on surface. (4) hand over the floor after 48 hours after the application. Make sure the material are full cured. 100 % strength  willachieve after 7 days.

MR. BOND POLYCHEM

SALES OFFICE : 12, Lakhu Goga Estate, Gota, Ahmedabad-380081, Gujarat, INDIA

Additional Information:

• Production Capacity: 10000 KG
• Delivery Time: WEEK
• Packaging Details: 800 GRAM, 6.6 KG, 26.5 KG

Epoxy Resin Machine Foundation Grout

WHERE TO USE:- Heavy Foundation of Plastic, Automobile, Mechanical Industries, Workshops, Sugar Industries, Distillery Units, Defense and artillery Units, Foundries, Installation of Heavy Equipments, Railways Bridges, Anchor Grout, Dam tunnel, Jetty’s, Turbine, Generators, Hydraulic presses, Lath M/C., etc.

Surface Preparation:- Surface should be Dry, clean, even and free from dust, dirt, paint, rust, Algee, grease, soluble salt, or other contaminations and Damp free. For cleaning use hand or power tools and cleaning chemicals / paint remover and then use rust remover or sand blasting wherever required.

Additional Information:

• Item Code: EFG-06
• Port of Dispatch: Pipavav or Mumbai
• Production Capacity: 10 Tons
• Delivery Time: 15 Days After PO
• Packaging Details: 50 Kg. & 200 Kg.

BOND GROUT –POAG - 01

POLYESTER ANCHOR GROUT

POLYESTER ANCHOR GROUT It is two pack polyester resin based anchoring or grouting material used in the form of mortar. Part-A & B are mixed before use in overhead or horizontal applications. The thyrotrophic consistency of the mix prevents the grout from flowing out of the hole.

WHERE TO USE:- . Uses Foundation bolts base and stress anchor· plates Tie-back anchors· Overhead rail tracks· Starter bars and dowels· Advantages Rapid strength gain· Vibration resistant· Corrosion resistant· Non - expansive· Can be placed under water·

SURFACE PREPARATION:- Ensure all the sides are roughened and dust free. To clean the holes thoroughly, using oil free compressed air. Thoroughly flush the substrate with water. Surface should be Dry, clean, even and free from dust, dirt, paint, rust, Algee, grease, soluble salt, or other contaminations

METHOD OF USE:- Pour Part-A into a pan. Add Part-B from the tin container. Mix the two to produce a smooth thixotropic paste. Mixing may be carried out mechanically or manually using gloved hands. Pour the mix into the hole and fasten the bolts, hooks or anchors. For cleaning use hand or power tools and cleaning chemicals / paint remover and then use rust remover or sand blasting wherever required. EPAG-01 packs have been designed to produce practical and economic volumes of grout. Do not mix partial pack components

Additional Information:

• Production Capacity: 10000
• Delivery Time: 15 DAYS
• Packaging Details: 2 TO 20 KG

BOND –WR-01

FOR CARS AND BUILDINGS

ECO FRIENDLY NANO COAT

WATER REPPALLENT FOR GLASS, PAINTS

WR-01NANO COAT is formulated for WATER REPPALLENT & weatherproofing, It forms invisible Nano coatings on the surface and give resistance to   water, pollutions, Dust, UV protection, Anti bacterial, Anti corrosive, and protect from acids, alkalis, saline weather, water based chemicals, mould, algee  and fungus growth.It can be used for exterior and interior use also.• Glass facades/ Glass Roofs

 ADVANTAGES

Ø  Free of fluorocarbon

Ø  Water based formulations

Ø  No heat necessary for activation

Ø  Saving of energy

Ø  Cross linking with surface

Ø  Excellent Water repellence •Resistance to Dust, Dirt, Mould, Algee, etc

Ø  UV Protection

Ø  Save some electricity due to dry air in the rooms due to nano coat reduce load for  Air-Condition.

Ø  Protects glass from corrosion (acid rain etc.) 

Ø  Transparent Nano coat. 

Ø  Very good temperatures resistance.

Ø  Low Cleaning and Maintenance requirements. 

Ø  Eco friendly.

WHERETOUSE:-Use On Glass like window, panel, door, Architectural, auto, decorative and solar panel glass and on paint for surface sealing. Glass of building, Cars, offices, homes,  wall,  means where glass and paints are required to water repellent.

METHOD OF USE:- (1)  SURFACE PREPARATION:- Surface should be Dry, clean, even and free from dust, dirt, paint, rust, Algee, grease, soluble salt, or other contaminations and Damp free. For cleaning use cleaner. Coating should be applied and dried in a dust free environment, preferably in clean room conditions.

Additional Information:

• Item Code: BOND-06
• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer)
• Port of Dispatch: Pipavav or Mumbai
• Production Capacity: 10 Tons
• Delivery Time: 15 Days After PO
• Packaging Details: 50 Kg. & 200 Kg.

Bond Lsr-01 Liquid Silicone Rubber For Mould
This Products Are Used For Mould Making For Stones, Articals, Statues, This Is A Very Good Products And Are Giving Mould Bubble Free. And Can Use At Your Place Without Any Machinery. Anybody Can Make A Mould.

Additional Information:

• Port of Dispatch: Nhavashiva Pipavav
• Production Capacity: 10000 kg
• Delivery Time: 15 days
• Packaging Details: 50 KG

BOND-AD-01 , 02 & 03

POLYMER –CEMENT TILE & BOARD ADHESIVE

BOND TILE ADHESIVE is a dry pre-mixed factory made, adhesive mortar for laying/fixing Tiles, Stones, blocks, Cement penal Board, bricks, Tiles on tiles and other similar masonry units. This is polymer modified and only requires the addition of clean water.

ADVANTAGES

* Quality controlled and factory made to give a consistently high quality product. * Excellent workability.

* High adhesive properties. * Shrinkage resistant. * Mix by hand or electrical mixer. *Reduces wastage.

*Suitable for interior or exterior use.*Strengths greater than that of the ordinary cement mortar.

AD-01 is particularly useful for bonding, laying tile, stone, board etc. suitable for vertical and horizontal surfaces.

TECHNICAL INFORMATION

Additional Information:

• Item Code: EPG-01
• Production Capacity: 150000
• Delivery Time: 15 dyas
• Packaging Details: 3,5,10,20